non hyundai question, (but I like hyundaitech's advice!!)

  • Thread starter Thread starter Andre
  • Start date Start date
A

Andre

while this problem isn't happening on a hyundai, it concievably could......

I just picked up a backup car, a 93 olds achieva with a dohc 4 cyl.

found out from service records that one spark plug is cross threaded. what
options does one have when this plug stops working? will the head need to
be pulled, or is there an easier solution?

hopefully no one is too offended by my non-hyundai question, but I've been
on this NG for about a year, and I kinda like talking to you people!!

thanks for any and all help.

andre
 
Andre said:
while this problem isn't happening on a hyundai, it concievably could......

I just picked up a backup car, a 93 olds achieva with a dohc 4 cyl.

found out from service records that one spark plug is cross threaded. what
options does one have when this plug stops working? will the head need to
be pulled, or is there an easier solution?

hopefully no one is too offended by my non-hyundai question, but I've been
on this NG for about a year, and I kinda like talking to you people!!
Click to expand...

It really is a question you should take to alt.autos.gm. Of course we're
all nice guys here, but there really is a newsgroup for this question.
 
You won't know what's necessary until you get the old plug out. Many GM
techs use anti-seize on plugs to keep the threads from being damaged when
replacing plugs.

If it's not too bad, some anti-seize and a new plug may work fine.
Always
replace plugs on a GM engine when cold. Probably due to thermal
expansion,
most thread problems occur when servicing plugs on a warm engine. Or you
may be able to clean up the threads with a tap. Worst case, you'd need
to
install a helicoil. But tapping or drilling for the helicoil will
introduce shavings into the combustion chamber. They'll probably blow
out
with no damage, but the possibility of worse is always there.
 
hyundaitech said:
You won't know what's necessary until you get the old plug out. Many GM
techs use anti-seize on plugs to keep the threads from being damaged when
replacing plugs.

If it's not too bad, some anti-seize and a new plug may work fine.
Always
replace plugs on a GM engine when cold. Probably due to thermal
expansion,
most thread problems occur when servicing plugs on a warm engine. Or you
may be able to clean up the threads with a tap. Worst case, you'd need
to
install a helicoil. But tapping or drilling for the helicoil will
introduce shavings into the combustion chamber. They'll probably blow
out
with no damage, but the possibility of worse is always there.
Click to expand...

That's where a vac with a narrow nozzle comes in handy.
 
Reply to message from Brian Nystrom <[email protected]> (Wed, 15
Nov 2006 17:19:34) about "Re: non hyundai question, (but I like
hyundaitech's advice!!)":

BN> That's where a vac with a narrow nozzle comes in handy.

Narrow as in a straw ...

Best Regards
Wayne Moses <[email protected]> Wed, 15 Nov 2006 18:40:39 -0600

=== Posted with Qusnetsoft NewsReader 3.3
 
Thanks (as always) for the advice.

I promise from now on to only post hyundai related questions!!!

Andre


Reply to message from Brian Nystrom <[email protected]> (Wed, 15
Nov 2006 17:19:34) about "Re: non hyundai question, (but I like
hyundaitech's advice!!)":

BN> That's where a vac with a narrow nozzle comes in handy.

Narrow as in a straw ...

Best Regards
Wayne Moses <[email protected]> Wed, 15 Nov 2006 18:40:39 -0600

=== Posted with Qusnetsoft NewsReader 3.3
 
Back
Top